Gun enthusiasts want the best when it comes to protecting their firearms and customized finishes. Especially when those finishes include ferrous metals, wood, stainless steel, synthetics, and alloys. There is no heating or baking required. Here are a few tips on using DuraCoat Aerosol, and be sure to ask your Lawrence, KS supplier about Peel 'N Spray templates.
Some people like a smooth finish and others like some other type of texture. Just about any surface is possible with these products ranging from camo to a pearl texture. It is even possible to create layers of texture and then finish them off with a protective coating of the clear product to reduce dings and scratches.
One of the nice things about this product is the hardener that comes with it. The aerosol can is a can within a can and allows putting the hardener in without making a huge mess. The usual ratio of 12 parts DuraCoat to 1 part hardener, and greatly speeds up the drying process. Change the ratio to 10:1 for a higher glossy finish that shines like brand new.
When using templates that stick on the weapon, be sure to remove any residual adhesive materials before applying the product. A clean, dry rag and some mineral spirits will free up and remove the adhesive without damaging the project. Any residue left behind causes bubbles and other distortions that blemish the surface.
Typical drying time is overnight. Placing the weapon in an oven for just 1 hour and baking it for about an hour at 110 degrees F speeds up the drying process. At this point, it is possible to use abrasive solvents, lubricants, and cleaners without destroying the finish. For full curing time allow three to six weeks.
Keep in mind that DuraCoat is available in over 200 colors, including Clear and those 200 colors when mixed will match any color in the spectrum. The Aerosol Kit contains a spray can that easily allows mixing the dryer with the color mixture for perfect results and easy to access and clean up afterward.
The most important part of the whole process is to clean the weapon and all its parts. Dismantle it and place the parts in some order that help you remember how they go when putting the gun back together. DuraClean is excellent because it removes all grease, grime, dust, dirt and any other debris without even leaving a film.
Always dismantle a gun for safety reasons before attempting to clean it, repair it, or refinish it. Make sure all compartments have no ammunitions in them. Check the cylinder, the bullet clip and chamber to make sure the gun is unloaded. Then dismantle it and mask off any areas not intended for DuraCoat before spraying the product on the pieces.
There is no such thing as too much safety when dealing with firearms that use explosives. When cleaning and oiling guns use the proper tools to dislodge any debris especially inside where dirt often collects. Then use the very best grade products to clean, maintain and customize your entire collection.
Some people like a smooth finish and others like some other type of texture. Just about any surface is possible with these products ranging from camo to a pearl texture. It is even possible to create layers of texture and then finish them off with a protective coating of the clear product to reduce dings and scratches.
One of the nice things about this product is the hardener that comes with it. The aerosol can is a can within a can and allows putting the hardener in without making a huge mess. The usual ratio of 12 parts DuraCoat to 1 part hardener, and greatly speeds up the drying process. Change the ratio to 10:1 for a higher glossy finish that shines like brand new.
When using templates that stick on the weapon, be sure to remove any residual adhesive materials before applying the product. A clean, dry rag and some mineral spirits will free up and remove the adhesive without damaging the project. Any residue left behind causes bubbles and other distortions that blemish the surface.
Typical drying time is overnight. Placing the weapon in an oven for just 1 hour and baking it for about an hour at 110 degrees F speeds up the drying process. At this point, it is possible to use abrasive solvents, lubricants, and cleaners without destroying the finish. For full curing time allow three to six weeks.
Keep in mind that DuraCoat is available in over 200 colors, including Clear and those 200 colors when mixed will match any color in the spectrum. The Aerosol Kit contains a spray can that easily allows mixing the dryer with the color mixture for perfect results and easy to access and clean up afterward.
The most important part of the whole process is to clean the weapon and all its parts. Dismantle it and place the parts in some order that help you remember how they go when putting the gun back together. DuraClean is excellent because it removes all grease, grime, dust, dirt and any other debris without even leaving a film.
Always dismantle a gun for safety reasons before attempting to clean it, repair it, or refinish it. Make sure all compartments have no ammunitions in them. Check the cylinder, the bullet clip and chamber to make sure the gun is unloaded. Then dismantle it and mask off any areas not intended for DuraCoat before spraying the product on the pieces.
There is no such thing as too much safety when dealing with firearms that use explosives. When cleaning and oiling guns use the proper tools to dislodge any debris especially inside where dirt often collects. Then use the very best grade products to clean, maintain and customize your entire collection.